Welcome To - Taizhou Huangyan Yige Machinery Co., Ltd.!Home - contact us - Online Message

Call Us on

15967672923
15967672923
Category
contact us

Company Name: Taizhou Huangyan Yige Machinery Co., Ltd. Contact: Manager He Phone: 15967672923
Company mailbox: 2562261439@qq.com
Company Address: Shangye Industrial Zone, Jiangkou Street, Huangyan District, Taizhou City

newsYou are here: Home - news - Content
How should blow molding machine manufacturers pay attention to production safety issues
Edit:Taizhou Huangyan Yige Machinery Co., Ltd.   UpDate:2019-07-03

The safety of the times has become the consensus of people. A blow molding machine manufacturer is no matter how efficient and simple, if it loses its safety, it will lose its due application value. In recent years, safety accidents caused by bottle blowing machine manufacturers have repeatedly appeared

Strengthen production and equipment management, improve the operating level of operators, ensure the safety of production equipment, improve labor productivity, ensure continuous and stable production, ensure product quality, and reduce production costs.

The necessary knowledge of the safe operation specifications of the blow molding machine manufacturers has the following points:

1. Lubricating oil must be applied to each moving part before each shift is started. (Manipulator, manipulator guide, mold opening and closing guide)

2. The arm can be added once every day (3-4). The large and small chains of the heater can be used once a month. Always check whether the reducer of the main engine or the reducer of the heater is short of oil. The host bearing can be added once every (2-3) months.

3. Before production, check whether the moving parts are strong, whether the screws are loose and dropped, especially where the impact force is strong, and whether the belt drive part is abnormal.

4. Check whether the high-pressure gas source, low-pressure gas source, power source, and water source are normal.

5. Check each emergency stop switch, safety door switch and protection device to check whether the switch is normal.

6. Check whether the heating head enters the embryo and whether the embryo is working properly. If the insert is not in place, the nut can be adjusted.

7. Check whether the lamp is damaged or broken. To be replaced in a timely manner.

8. Check whether each pneumatic component leaks air and whether it is active.

9. Check whether the triplet leaks abnormally, if it is blocked, and whether the water storage capacity of the water cup is too full.

10. When the solenoid valve of the bottle blowing machine manufacturer is abnormal, it should be cleaned in time (cleaning once every 3.5 million bottles).

11. The blow mold must be cleaned and polished regularly.

12. When you turn on the bump pressure air source switch, you must move slowly to prevent dirt from blowing into the solenoid valve too quickly. Open the exhaust valve together for 30 seconds to ensure clean air.

13. When the machine is started, it must be ensured that the mechanical part is good, and there are no people and no foreign objects inside the machine. Especially the position of the crank to avoid hurting people. Close the security door together.

14. When starting the machine, the motor must be started first, and the heater should be started with a delay of 30 seconds to prevent the voltage from shaking. Make sure the cooling water is turned on before starting the heating.

15. After heating (2-3) minutes, wait until the temperature of the oven rises evenly, and then press the embryo button. Blowing the bottle together with the power should also be turned on, otherwise it will not blow the bottle.

16. When the machine is working, you must pay close attention to whether the machine has abnormal noises. It must be detected early and stopped in time for early treatment.

17. When there is an urgent situation, press the emergency stop button to apply the brakes. Then analyze the cause of the formation according to the situation on the spot, find the problem and deal with it quickly.

18. After the machine works normally, do not put any part of the body into the machine to avoid injury to the manipulator. If the machine has abnormal noise, it can be investigated after deceleration.

19. After the machine is in normal production, the operator must constantly investigate the quality of the bottle to avoid fluctuations in voltage or other reasons affecting the quality of the bottle.

20. When the machine is repaired, press the touch screen fault repair button to ensure safe repair.

If you need to manually investigate the movement of each cavity individually, please pay attention to the orientation of the robot. Together, be sure to understand the role of the button alone, and then move. Ensure that malfunctions cause unnecessary trouble.

twenty one. After repairing the machine every time, be sure to organize things such as tools and screws to avoid leaving them in the machine and affecting the normal work of the machine.


Mobile